6L 2 1 Ratio Epoxy Resin River Art Resin Fast Cure Ultra-Clear Casting
6l river art resin fast cure 2:1 epoxy resin ultra-clear voc free. Unleash the maker in you, pour-layer-spray-brush to create whatever you need this be. Mix well with mica powders, inks and dyes. There are endless amounts of ideas you can create invent make anything you want. For casting use, make sure you use a pressure chamber to remove all the bubbles.
How to work with 2:1 fast cure resin. Please note: this is to be used when temperature is 25c. If the temp is lower, this will increase the working times. If warmer, it will lessen the working time.
How much quantities to mix at a time. Because it is a fast-curing type, the reaction speed is faster after mixing. It is usually recommended not to mix too much at one time. 100 grams or 300 grams are the reference quantities. If a lot of mixing is required for actual work, it must be poured at the same time, .And do not let the mixture stay in the container for more than 15mins. I'll give practical examples for each of these two mixed cases. 1.1 mix 90 grams at a time. Part a: 60 grams, part b 30 grams.
Prepare an empty container c, first pour 30 grams of b, then 60 grams of a. Slowly stir until it is clear and transparent, and there is no wire drawing state.
It is recommended for 1-2 minutes. Wait for 1-2 minutes, the purpose is to pour the resin immediately after the large bubbles disappear and the resin is not hot. If you need to add pigment, add the pigment at a&b mixing stage. If you do not need to add pigment, this step can be omitted. Start pouring, pour the mixed 90g mixture into different molds at one time, . Pay attention to the thickness, one mold should not exceed 1cm--2cm, this 90g mixture can be poured into many different molds. 1.2 mix 300 grams at a time. Steps: the steps are the same as above. Start pouring, pour the mixed 300g mixture into different molds at one time, pay attention to the thickness, . One mold should not exceed 1cm--2cm, this 300g mixture can be poured into many different molds.Make sure at the end not any mixture left over is in the container otherwise it will solidify the next time you pour. How long does it take for 2:1 fast dry resin. 2:1 fast-curing resin is a type of resin with excellent performance and high quality.
Because of its quick-drying performance, it is favoured by customers using it for a wide range of applications. It can be used to make all kinds of jewellery, earrings, necklaces, pendants, and chopping boards etc. Remarks: the thickness of 2:1 quick-drying pouring cannot exceed 1cm -2cm.As long as the thickness does not exceed this range, even if you make a surface as large as a table. The operation time is 3---5 minutes (maximum time of 10mins), and the setting time is 30 minutes -1 hour. Mix 2:1 by weight ratio. 6l size (4l part a and 2l part b).
Why choose river art resin epoxy. Crystal clear finish: cures crystal clear. Suitable for wooden bar tops, river tables, jewellery, & more. Uv resistant: added uv inhibitors resist yellowing when exposed to the sun and ultra violet light.
Self-level mixture: our epoxy will self-level over leaving a consistent thickness. Bubble-free: epoxies may bubble, easily releases all bubbles due to low viscosity, can be used with a heat gun to increase release speed. Impact resistant: cures super strong, leaving a smooth impact-resistant surface.Minimal odour and not at all yellowing after a long period of time. River art resin epoxy will leave your projects with a solid, uv resistant, impact resistant high gloss finish. Don't ruin a one-of-a-kind project with a cheap epoxy.
This ultra/crystal clear epoxy resin is a top of the line' water clear superior performance epoxy system that can be used for so many applications including casting, jewellery, surfboards, bench tops, boat repairs, floor and bench top coating. Following factors affect the curing time. Mixing quantity (the more you mix, the fast it cures and vice versa). Room temperature (higher room temperature will speed up the curing).
Mixing ratio: 2:1 (2 parts a and 1 part b). Viscosity: 600 cps for part a. 450 cps for part b.
Item code: 2:1 epoxy 6l.